• Welcome, Guest! We hope you enjoy the excellent technical knowledge, event information and discussions that the BMW MOA forum provides. Some forum content will be hidden from you if you remain logged out. If you want to view all content, please click the 'Log in' button above and enter your BMW MOA username and password.

    If you are not an MOA member, why not take the time to join the club, so you can enjoy posting on the forum, the BMW Owners News magazine, and all of the discounts and benefits the BMW MOA offers?

KGT Wheel Removal (2009)

Ensure proper thread engagement of the caliper bolts and torque to 30 Nm (22 ft-lbs)
 

Attachments

  • 18 r calp 3.jpg
    18 r calp 3.jpg
    69.3 KB · Views: 212
Prior to installing the fender back on you may want to check the threads as mine were slightly corroded.

I chased the threads with an M6 x1.0 Tap
 

Attachments

  • 19 top mounting hole.jpg
    19 top mounting hole.jpg
    43 KB · Views: 210
CRITICAL FINAL STEP

You need to pump the front brake lever to set the caliper pucks back position onto the discs for the brakes to work correctly

Shown below is the very first pump action - as you can see the brake lever is at its normal position
 

Attachments

  • 25 brake pump 1.jpg
    25 brake pump 1.jpg
    51.4 KB · Views: 212
Last edited:
Now the lever is pumped and reaches all the way to the bar.

That is why you do this in the garage and not on the road!!
 

Attachments

  • 26 brake pump 2.jpg
    26 brake pump 2.jpg
    41.1 KB · Views: 214
After a few pumps the pads are set in the front caliper and you will have proper lever action to safely activate the brakes.
 

Attachments

  • 27 brake pump 3.jpg
    27 brake pump 3.jpg
    48 KB · Views: 194
Rear Wheel Removal

Removal process:

  1. Remove Exhaust pipe cover guard
  2. Loosen Exhaust clamp
  3. Remove Exhaust Hanger Bolt
  4. Remove exhaust
  5. Remove Wheel

Starting with the Exhaust pipe cover guard use a T25 to remove
 

Attachments

  • 01 - exhaust shield.jpg
    01 - exhaust shield.jpg
    50.9 KB · Views: 195
Last edited:
There is a tongue and groove interface feature on the back side of the guard
 

Attachments

  • 03 - shield clip 2.jpg
    03 - shield clip 2.jpg
    54 KB · Views: 197
Loosen Exhaust clamp using a T45 torx
 

Attachments

  • 04 - clamp.jpg
    04 - clamp.jpg
    59.4 KB · Views: 196
Last edited:
After you have loosened the clamp you need to remove the Exhaust hanger bolt.

CAUTION - ensure you are supporting the exhaust as this is the last mechanical securing item
 

Attachments

  • 05 muffler hanger.jpg
    05 muffler hanger.jpg
    56.3 KB · Views: 195
SHOP TIP - After you remove the muffler you will have the exhaust system open - to prevent any foreign material to fall in you may want to stuff a rag to prevent such an occurrence.
 

Attachments

  • rag.jpg
    rag.jpg
    62 KB · Views: 196
Last edited:
Put the bike in gear and remove the wheel bolts using a T-50
 

Attachments

  • 06 - wheel off.jpg
    06 - wheel off.jpg
    68.5 KB · Views: 196
The replacement process for the rear wheel is as follows

  1. Install wheel onto rear hub
  2. Install Wheel Lugs and torque to spec
  3. Install muffler
  4. Mount hanger
  5. Tighten exhaust clamp
  6. Install exhaust cover shield


IMPORTANT NOTE - The Wheel bolts DO NOT get any lubricant or locking material applied to them, they go in dry, they come out dry
 

Attachments

  • 07 dry bolt.jpg
    07 dry bolt.jpg
    36.2 KB · Views: 195
Last edited:
Below shows the tire mounted onto the rear hub.

The wheel bolts have been put in, hand tight, ensuring the wheel is properly seated then torque as outlined.

The torquing sequence is a diagonal pattern shown below:

1 to 2

2 to 3

3 to 4

4 to 5

Tighten to 60Nm (44 ft-lbs)
 

Attachments

  • Tighten sequence.jpg
    Tighten sequence.jpg
    70.5 KB · Views: 194
Last edited:
The next step is mounting the muffler, it is a two step process.

The first mouting is the muffler onto the exhaust opening (Green arrow) and then swinging the muffler up onto the top mount location (Blue Arrow).
 

Attachments

  • 02  muffler mount.jpg
    02 muffler mount.jpg
    88.3 KB · Views: 193
Mount the muffler handing bolt hand tight as you need to ensure that the muffler is properly spaced to the rear wheel.
 

Attachments

  • 03 hanger mount.jpg
    03 hanger mount.jpg
    53.1 KB · Views: 194
Ensure that there is 10mm of spacing between the muffler and the rear wheel

Shop Tip - by having the muffler hanger and muffler clamp hand snug - you can position the muffler to be in the proper alignment before completely tightening.
 

Attachments

  • Spacing.jpg
    Spacing.jpg
    44.7 KB · Views: 194
Last edited:
Once the spacing is set tighten the muffler clamp to 35Nm (26 ft-lbs)

Then tighten the muffler hanger to 22Nm (16 ft-lbs)
 

Attachments

  • 04 clamp tightening.jpg
    04 clamp tightening.jpg
    55.6 KB · Views: 195
Last edited:
Back
Top