Results 1 to 8 of 8

Thread: Heated Grips for 2020 F850GSA

  1. #1

    Heated Grips for 2020 F850GSA

    Hello everyone, I'm wondering if anyone has any suggestions as to which brand of heated grips would fit on a 2020 F850GSA. I purchased a pair of R&G Premium Grips, but the shop told me that they would not fit the handlebars because of the complexity of the current grips and system. Instead they suggested the OEM grips which run near $1000....I'm thinking that's quite a bit much for heated grips.

    Has anyone successfully installed any aftermarket grips? Thank you!

  2. #2
    SURVIVOR akbeemer's Avatar
    Join Date
    Jul 2007
    Location
    Big Sky Country
    Posts
    8,661
    Welcome to the forum.

    Sounds to me like you may want to try a different shop. There is nothing magic about BMW handlebars.

    I've had Oxford grips on three bikes and they are a fine product. Get hotter than any BMW grips I've ever had and never failed. They have an automatic shut-off if they sense low voltage. I suspect your shop was concerned about running aftermarket heated grips on your bike because of the CANBus electrical system. Because of the CANBus, you will need to run them directly off the battery on a fused circuit, or better still off of a fuse block or power distribution module that provides switched power.
    Kevin Huddy
    Silver City, Montana
    MOA# 24,790 Ambassador

  3. #3
    Thank you Kevin,
    The main issue that we saw was that the sizing was off. They some other handlebars and grips lying around so we took the time to compare the inner diameters of the grips compared to the other grips, throttle and the bars. What we found was that the left R&G grip fit just fine, but that the right R&G grip left too much space between it and the throttle. I'm wondering if it's just the R&G grips and that maybe the Oxford grips would work, as you suggested. It's going to take some more investigation...

    Cheers!

  4. #4
    Fortis Fortuna Adiuvat Omega Man's Avatar
    Join Date
    Jan 2010
    Location
    Mansfield,MA
    Posts
    16,719
    Welcome to the forum!
    I find the heated grips on the F800GS just ok. Best when it happens to get chilly when you were not expecting it. With gloves, the heated grips are insulated from your hands unless you have snowmobile style gloves with less insulation in the palm area.
    Heated mitten style gloves may be a way to go for you.
    Just a thought.
    Enjoy the forum.
    Gary
    "You can do good or you can do well. Sooner or later they make you choose." MI5
    Mod Squad
    2009 F800GS 1994 TW200

  5. #5
    Well now, think about this. The inner diameter of the two twist grips needs to be different. The left grip fits on the handlebar, be it a 7/8" or 22mm as BMW uses. The right grip fits over the sleeve that is the twist portion of the throttle, which itself fits over the bare bar.

    If the heater goes over the existing grips fine. If they replace them then they bust be different inner diameters. So what goes where matters a lot.
    Paul Glaves - "Big Bend", Texas U.S.A
    "The greatest challenge to any thinker is stating the problem in a way that will allow a solution." - Bertrand Russell
    http://web.bigbend.net/~glaves/

  6. #6
    Right, when we looked until the stock grips we could see that they would just slip on like they're suppose to and that the throttle was actually thinner than expected leaving too much gap on the inner right. Seems like BMW did not want it to be so simple like on a Japanese bike for example.

    I'm considering my options and going to try some heated glove liner to fit them into my existing "winter gloves". Depending on that I can make a good choice I hope!

  7. #7
    Registered User drneo66's Avatar
    Join Date
    Jun 2009
    Location
    Rochester, MN
    Posts
    927
    Bummer - I can also see where the "wonderwheel" could interfere with the oxfords.

    In my personal experience, heated gloves or glove liners will warm your hands much better than heated grips, but they do take space and planning to make sure you have them when you need them.


    I haven't personally installed them, but I wonder if you can utilize the thin heated elements that would go under your OEM grips.

    Otherwise, maybe take a look at the Oxoford over-grip wraps - though somewhat inconvenient, they may be another option.
    Current: 2007 BMW R1200RT, 2013 F800GS
    Former: 1995 BMW K75S, 2009 BMW G650GS
    MOA Member #:150400, IBA#: 37558

  8. #8
    Registered User GTRider's Avatar
    Join Date
    Apr 2006
    Location
    Nibley, UT USA
    Posts
    1,968
    Oxford grips are trimmable and lefts/rights can be purchased individually as replacements or if one is adjusting a length issue.

    Best,
    DeVern
    DGerber
    1983 R80ST 1984 R80 G/S-PD 2004 K1200GT w/Hannigan S/C 2010 K1300GT 2018 R1200GS
    BMWMOA#52184, AMA#271542, IBA#138

Similar Threads

  1. Heated grips
    By monsterkingdaddy in forum New Members
    Replies: 2
    Last Post: 10-03-2019, 04:19 PM
  2. Replies: 24
    Last Post: 11-30-2013, 03:15 PM
  3. Replies: 28
    Last Post: 02-25-2010, 12:27 AM
  4. Heated grips or Heated gloves??
    By SweetT in forum Gear
    Replies: 12
    Last Post: 11-30-2004, 04:25 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •