Results 1 to 9 of 9

Thread: throttle body sync

  1. #1

    throttle body sync

    hi all.. i have a '99 R1100RT.. dies out at stop signs.. not all the time , occasionally.. Idle is right at 1100 rpm, seems to be right on..
    do you think this is a throttle body sync issue, or valve adjustment.. Thank you, Rich

    also.. do you need to remove tupper ware to make adjustment?

  2. #2
    Registered User m_stock10506's Avatar
    Join Date
    Feb 2005
    Location
    Trinity, NC
    Posts
    964
    Yes. Remove the fairings. Do a valve clearance check or adjustment. Take the bike for a 20 minute ride and do a throttle body sync.

    Once this is done, you will have a baseline so that you can diagnose any further running issues that come up.

    I would continue this with, do you have a service history for the bike? Do you know when the fuel filter was last changed?
    Michael Stock, Trinity, NC
    R1100RT, R100, R60/6

  3. #3
    Pepperfool GSAddict's Avatar
    Join Date
    Feb 2008
    Location
    Sechelt, British Columbia
    Posts
    3,134
    Before doing the sync, count the turns closed, then remove the big brass screw on each throttle body and clean them.
    They get gummed up.
    Clean the bores with a Q tip dipped in solvent.
    Lightly lube the O ring on the screw.
    Replace the screws to the recorded turns out.
    Start your sync.
    '
    Ufda happens..........

    Need your R11xx Hall sensor rewired? PM me.

  4. #4
    Does your bike surge (aka hunt) at small throttle openings? If so, try the Zero = Zero synch method, developed by MOA Member Rob Lentini (may he RIP)

    If your bike does not surge, I would not advise you to use this technique.

    Ian
    Go soothingly through the grease mud, as there lurks the skid demon.
    __________________________________________________ __________________________________
    '67 Trail 90 || '86 R80 G/SPD+ || '97 F650ST || '00 1150 GS || '07 Xchallenge || '13 CB500X || '14 Grom

  5. #5
    Registered User roger 04 rt's Avatar
    Join Date
    Oct 2011
    Location
    Florida & Massachusetts
    Posts
    1,999
    Quote Originally Posted by Visian View Post
    Does your bike surge (aka hunt) at small throttle openings? If so, try the Zero = Zero synch method, developed by MOA Member Rob Lentini (may he RIP)

    If your bike does not surge, I would not advise you to use this technique.

    Ian
    Rob was an early experimenter with Oilheads and made many important tests. As with all technology, those that come later stand on the shoulders of those who came before. In this case, later research showed that zero=zero was wrong and should not be used.

    The last thing one should try as a last resort is realigning the TB stop screws. If one needs to though, the correct zero=250 procedure is here at step 1.5: https://forums.bmwmoa.org/showthread...=1#post1091142

  6. #6
    Registered User m_stock10506's Avatar
    Join Date
    Feb 2005
    Location
    Trinity, NC
    Posts
    964
    With all respect to the original poster and the other good suggestions made.... the original post involved a very basic question regarding one of the most simple and routine maintenance procedures. My feeling here is that the suggestions offered should be more in line with the apparent wrenching level of the original poster. Just my.02.
    Michael Stock, Trinity, NC
    R1100RT, R100, R60/6

  7. #7
    Registered User roger 04 rt's Avatar
    Join Date
    Oct 2011
    Location
    Florida & Massachusetts
    Posts
    1,999
    +1, but people do come back later and read the threads.

  8. #8
    When a poster asks whether the plastic has to come off to perform a certain service I assume an unfamiliarity with that bike or that service. That is not a negative. But replies ought to reflect that fact and helpfully guide the poster on how to proceed.

    During the 20 years I wrote "Benchwrenching" I had to walk that fine line to address both the novice and the experienced at the same time without losing the novice or boring the experienced. We need to try to do the same here.
    Paul Glaves - "Big Bend", Texas U.S.A
    "The greatest challenge to any thinker is stating the problem in a way that will allow a solution." - Bertrand Russell
    http://web.bigbend.net/~glaves/

  9. #9
    Registered User dieselyoda's Avatar
    Join Date
    Mar 2013
    Location
    Winnipeg, MB, Canada
    Posts
    1,495
    Quote Originally Posted by PGlaves View Post
    When a poster asks whether the plastic has to come off to perform a certain service I assume an unfamiliarity with that bike or that service. That is not a negative. But replies ought to reflect that fact and helpfully guide the poster on how to proceed.

    During the 20 years I wrote "Benchwrenching" I had to walk that fine line to address both the novice and the experienced at the same time without losing the novice or boring the experienced. We need to try to do the same here.
    Starting simple is never the wrong thing to do, like asking simple questions. Even very, very experienced wrenches forget simple.

    Once you are over your head, ask more questions. Very, very experienced wrenches know that sharing the wealth, so to speak, builds experience, for both.

    Not every answer you might get will be the right one for you.

    Look at failure as adding to your experience.
    1997 R1100RT, 1981 KZ 440 LTD, R80RT, R90/6 sidecar, K1100RS,1983 K100RS (Cafe now)

    “The major civilizing force in the world is not religion, it is sex.”

Similar Threads

  1. My DIY Throttle Body Sync
    By bullfighter in forum Oilheads
    Replies: 19
    Last Post: 11-30-2017, 03:23 AM
  2. Throttle Body sync.
    By samo in forum Oilheads
    Replies: 16
    Last Post: 12-27-2011, 04:07 PM
  3. Throttle Body Sync
    By ronbo in forum Oilheads
    Replies: 9
    Last Post: 09-07-2011, 01:09 AM
  4. Throttle Body Sync
    By 142434 in forum Oilheads
    Replies: 1
    Last Post: 03-07-2009, 09:16 PM
  5. Throttle Body Sync?
    By JK in forum Hexheads/Camheads
    Replies: 16
    Last Post: 02-27-2008, 12:09 AM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •