Results 1 to 4 of 4

Thread: ABS Blinking

  1. #1
    Registered User
    Join Date
    May 2018
    Location
    Thousand Oaks, Ca.
    Posts
    39

    ABS Blinking

    I'd hate to think this is an oft repeated dialog but I can't seem to find a blinking ABS thread through the search.

    my 2000 r1100rt (112k miles) has the alternating red light ABS blinking and...I think this was brought on right after a hard front end pothole hit that actually shook the mirrors off. Could that warning light be from the front ABS sensor being knocked about? Or is that usually a unit failure? Is there a way to test this?
    I did a Youtube "reset" by grounding the plug in connector and holding the ABS button down...but that didn't do anything.

    If this is old territory, please send me links or the key to searching these threads effectively. Thanks!

  2. #2
    Pepperfool GSAddict's Avatar
    Join Date
    Feb 2008
    Location
    Sechelt, British Columbia
    Posts
    3,134
    Start here. Closely inspect the Front ABS sensor and all the way up the wiring right up to the connector where it joins the main harness
    Check the sensor gap
    Try to determine if there is a stored fault code. ABS 2 procedure.
    http://largiader.com/abs/absfault.html
    https://advrider.com/f/threads/abs2-...eadout.457863/
    Theory of operation
    http://largiader.com/abs/abs2.html
    '
    Ufda happens..........

    Need your R11xx Hall sensor rewired? PM me.

  3. #3
    Registered User m_stock10506's Avatar
    Join Date
    Feb 2005
    Location
    Trinity, NC
    Posts
    964
    Try the reset again. Even if there is a problem, the reset should get you back to the lights blinking together at key-ON at least the first time.

    This is from Anton's ABS Faults web page that GSAddict pointed you to above.

    Resetting ABS2 on early bike
    • Locate the diagnostic connector under the seat. Remove it from the blanking plug.
    • Insert one end of 20 cm wire into the middle socket of this connector.
    • Ground the other end firmly to a metal bolt in the area (and keep grounded).
    • Turn on ignition. You should see the lights flash alternately.
    • Hold ABS button down for about 8 seconds. The bottom ABS light will stay on, and the top one off.
    • Release the ABS button. If you have successfully reset the ABS, both ABS lights will come on. If you have failed to count to 8, or your ground is not good, the top ABS light will stay off.
    • Turn off ignition, remove wire.
    Michael Stock, Trinity, NC
    R1100RT, R100, R60/6

  4. #4
    Registered User
    Join Date
    Oct 2015
    Location
    SO CAL
    Posts
    57
    Can also be a weak battery

Similar Threads

  1. ABS Brakes 4x blinking and servo out on 2006 R1200GS
    By rivars in forum Hexheads/Camheads
    Replies: 3
    Last Post: 11-02-2011, 02:49 PM
  2. Blinking head light
    By wolverine in forum Hexheads/Camheads
    Replies: 30
    Last Post: 03-15-2010, 07:02 PM
  3. Another cause for a blinking ABS light
    By yellowrosefarm in forum Flying Brick K-bikes
    Replies: 0
    Last Post: 03-26-2009, 01:09 AM
  4. '04 K1200GT Brake Failure Light always blinking
    By Mudbug in forum Flying Brick K-bikes
    Replies: 5
    Last Post: 10-09-2008, 12:41 AM
  5. K75 RT ABS lights blinking after getting a jump
    By kevnallen in forum Flying Brick K-bikes
    Replies: 2
    Last Post: 04-19-2006, 10:06 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •