Results 1 to 13 of 13

Thread: R1150RT Spiegler Brake Line Install Tips?

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Registered User tangoalpha's Avatar
    Join Date
    Dec 2016
    Location
    CA Central Coast
    Posts
    310

    R1150RT Spiegler Brake Line Install Tips?

    Hi Guys.

    You may recall in a recent post where I mentioned ordering a set of fully sintered brake pads and a set of Spiegler SS braided brake hoses for my Ď02 R1150RT. Well the pads and the brake lines have arrived. Before I start wrenching, what Iíd like to know is whether any of you have any tips or advice on how best to replace the brake lines on my bike to minimize air getting in to the ABS system. As you might remember my bike has the servo assisted ABS braking system. Aka...whizzy brakes.

    After installing the brake lines & pads I will bleed the system. I researched the procedures & have the funnel which screws on the the front/rear brake circuit. Any input from those of you who have done this procedure before a whizzy brake equipped bike would be greatly appreciated.


    Sent from my iPhone using Tapatalk
    "Der Bimmer ist wunderbar."

    Tango Alpha
    2002 R1150RT

  2. #2
    Pepperfool GSAddict's Avatar
    Join Date
    Feb 2008
    Location
    Sechelt, British Columbia
    Posts
    3,088
    Have you read this? It covers the subject well especially the control bleed sequence.
    https://advrider.com/f/resources/abs-3-service-v2-0.7/

    I do the control circuits first, then the power.
    Have some old terry towel rags moistened with water to contain/wipe up spills.
    '
    Ufda happens..........

    Need your R11xx Hall sensor rewired? PM me.

  3. #3
    Registered User tangoalpha's Avatar
    Join Date
    Dec 2016
    Location
    CA Central Coast
    Posts
    310
    Quote Originally Posted by GSAddict View Post
    Have you read this? It covers the subject well especially the control bleed sequence.
    https://advrider.com/f/resources/abs-3-service-v2-0.7/

    I do the control circuits first, then the power.
    Have some old terry towel rags moistened with water to contain/wipe up spills.
    GSA,

    Thanks for the tips and the article. I clicked on the link and it appears the website server couldnít be found. Iíll try it again later. I appreciate your help very much.


    Sent from my iPhone using Tapatalk
    "Der Bimmer ist wunderbar."

    Tango Alpha
    2002 R1150RT

  4. #4
    Pepperfool GSAddict's Avatar
    Join Date
    Feb 2008
    Location
    Sechelt, British Columbia
    Posts
    3,088
    Quote Originally Posted by tangoalpha View Post
    GSA,

    Thanks for the tips and the article. I clicked on the link and it appears the website server couldnít be found. Iíll try it again later. I appreciate your help very much.


    Sent from my iPhone using Tapatalk
    It works now, just checked it.
    '
    Ufda happens..........

    Need your R11xx Hall sensor rewired? PM me.

  5. #5
    I just performed this on an 04. I had the dvd, the bmw maintenance doc and the above mentioned pdf. I had some issues getting dummy blocks that would work and had to fiddle with different size wood that I had. Be careful with the funnel and do not over tighten. I believe your module is different than mine, but be careful with any connectors you disconnect, etc. I disconnected one of the fluid level connectors and bent/broke the pin when re-inserting. I did not have to remove the connector for the work, but did so to cleanup fluid spillage. The brake lines themselves are relatively straightforward to replace, just take a look at the originals routing and angles and align the new with that. I got speed bleeders but never used them as i could access each of the levers and bleed at the same time. It was not overly complex, just takes time and have to methodically follow the bleeding sequence.

    good luck,
    -tp

  6. #6
    Registered User tangoalpha's Avatar
    Join Date
    Dec 2016
    Location
    CA Central Coast
    Posts
    310
    Quote Originally Posted by tpmcleod24 View Post
    I just performed this on an 04. I had the dvd, the bmw maintenance doc and the above mentioned pdf. I had some issues getting dummy blocks that would work and had to fiddle with different size wood that I had. Be careful with the funnel and do not over tighten. I believe your module is different than mine, but be careful with any connectors you disconnect, etc. I disconnected one of the fluid level connectors and bent/broke the pin when re-inserting. I did not have to remove the connector for the work, but did so to cleanup fluid spillage. The brake lines themselves are relatively straightforward to replace, just take a look at the originals routing and angles and align the new with that. I got speed bleeders but never used them as i could access each of the levers and bleed at the same time. It was not overly complex, just takes time and have to methodically follow the bleeding sequence.

    good luck,
    -tp
    Thanks for the tips and for the comment about the Speedbleeders. Much appreciated. I was nearly convinced that I needed to buy a set before attempting this. Not gonna lie to you, I'm really not looking forward to doing this project but it must be done. So I'm gathering all my information, resources, tools and materials before jumping in. I will go s-l-o-w-l-y and methodically, following all the steps, as you suggest being careful not to over tighten, bend or break anything. Hopefully it all turns out okay, despite my apprehension. Fingers crossed!
    "Der Bimmer ist wunderbar."

    Tango Alpha
    2002 R1150RT

  7. #7
    Registered User tangoalpha's Avatar
    Join Date
    Dec 2016
    Location
    CA Central Coast
    Posts
    310

    Thumbs up

    Quote Originally Posted by GSAddict View Post
    It works now, just checked it.
    Ditto! Thank a bunch. A great resource with step by step instructions and high res, color photos to boot! Exactly what I needed. I'll report back to let you know how it all turns out.
    "Der Bimmer ist wunderbar."

    Tango Alpha
    2002 R1150RT

Similar Threads

  1. Brake line install question
    By plock in forum Oilheads
    Replies: 6
    Last Post: 09-07-2015, 03:17 PM
  2. Spiegler Clutch Line, '00 R1150GS
    By gsbruce in forum Oilheads
    Replies: 2
    Last Post: 09-13-2012, 02:55 PM
  3. Spiegler brake lines
    By wzellwzell@yahoo.com in forum Oilheads
    Replies: 17
    Last Post: 11-16-2011, 07:58 PM
  4. 2004 K12RS Spiegler Steelflex Brake Line Installation
    By jurgen in forum Flying Brick K-bikes
    Replies: 0
    Last Post: 12-25-2010, 10:07 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •