• Welcome Guest! If you are already a member of the BMW MOA, please log in to the forum in the upper right hand corner of this page. Check "Remember Me?" if you wish to stay logged in.

    We hope you enjoy the excellent technical knowledge, event information and discussions that the BMWMOA forum provides. Why not take the time to join the club, so you can enjoy posting on the forum, the club magazine, and all of the discounts and benefits the BMWMOA offers?

    Want to read the MOA monthly magazine for free? Take a 3-month test ride of the magazine; check here for details.

  • NOTE. Some content will be hidden from you. If you want to view all content, you must register for the forum if you are not a member, or if a member, you must be logged in.

KGT Wheel Removal (2009)

Semper_Fi

Honey Badger
The articles, posts and comments in this tech section are posted by individual members and reflect their personal thoughts and experiences with repairing, maintaining, and generally working on motorcycles. This information may require specific knowledge and skills, may or may not be correct or current to model.

The authors of information found here and the BMW MOA take no responsibility for ensuring the accuracy of any information (including procedures, techniques, parts numbers, torque values, tool usage, etc.), or further for any damage of any kind or injuries incurred or caused by anyone following the instructions or information found here.

It is the duty of the individual to either assume the liability himself for responsibly using the information found here, or to take the bike or accessory to a Dealer or other qualified professional service.


Lastly, please ensure you dispose of your used chemicals, oils and fuels in an environmentally responsible manner. Most Auto Parts stores and service stations will accept used oil and lubricants, tires and batteries, please check for your local availability.

This article, text and photos are Copyright of the individual authors and the BMW MOA, any copying or redistributing is permitted only by prior written authorization.
 
This DIY will cover removing and installing the Front and Rear Wheel Assembly on a 2009 KGT 1300.

Tools

  • T20 for the ABS Sensor Bolt
  • T30 for the Fender Mounting Bolts
  • T45 for the Caliper Bolts
  • 3/8" drive torquewrench
  • Front Axle Socket - I use a Marc Parnes tool*
  • 19mm wrench or socket to use on the Axle Socket tool
  • Front Wheel Stand - I use a PitBull Stand*

* Not affiliated with manufacturer just utilize their products
 
Last edited:
Process Overview

  • Put the bike on centerstand
  • Remove front fender
  • Remove Calipers
  • Remove ABS Sensor
  • Remove Right Side (Throttle Pinch Bolt)
  • Loosen quick release axle
  • Lift front wheel with front stand
  • Remove axle
  • Remove Wheel Assembly
 
So let's start - put the bike on the centerstand.

Shop Tip - if you plan to take both tires off, and you plan to use a PitBull lift, you will want to remove the rear tire first.
 

Attachments

  • 01 - centerstand.jpg
    01 - centerstand.jpg
    69.1 KB · Views: 358
Using a T30 remove the indicated Fender Bolts (Throttle side)
 

Attachments

  • 02 - fender r.jpg
    02 - fender r.jpg
    54.1 KB · Views: 353
Last edited:
The pull straight out, the full fender comes off - set aside
 

Attachments

  • 04 - pull forward.jpg
    04 - pull forward.jpg
    49.6 KB · Views: 351
Unclip the ABS wire harness from the brake line. 2 locations
 

Attachments

  • 06 - abs clips.jpg
    06 - abs clips.jpg
    54.3 KB · Views: 353
To remove the caliper you need to spread the pads a little - this is easily done by twisting the caliper slowly as your are pulling it off.

As you pull back twist to push the pads apart a little.

DO NOT ACTIVATE THE BRAKES AS THIS WILL PUSH THE BRAKE PADS OUT
 

Attachments

  • 09 - grab and twist r.jpg
    09 - grab and twist r.jpg
    67 KB · Views: 354
Last edited:
Caliper removed, now onto the other side

NOTE - I left the caliper hanging because I was only going to be away for one day as the tires where being swapped - if you want feel free to support the caliper if so desired
 

Attachments

  • 10 - r caliper completely off.jpg
    10 - r caliper completely off.jpg
    69.2 KB · Views: 354
Last edited:
Using a T45 remove the other 2 Caliper mounting bolts
 

Attachments

  • 11 - left caliper off.jpg
    11 - left caliper off.jpg
    72.9 KB · Views: 354
Using the same twisting technique start removing the clutch side caliper
 

Attachments

  • 12 - grab and twist 2.jpg
    12 - grab and twist 2.jpg
    44.8 KB · Views: 347
Calipers are now removed, next is the ABS Sensor
 

Attachments

  • 13 - left caliper completely off.jpg
    13 - left caliper completely off.jpg
    74.7 KB · Views: 248
Using a T20 torx remove the ABS Mounting bolt
 

Attachments

  • 14 - ABS Bolt off.jpg
    14 - ABS Bolt off.jpg
    73.2 KB · Views: 248
Last edited:
Once the bolt is removed you can pull out the ABS Sensor
 

Attachments

  • 15 - abs sensor out 1.jpg
    15 - abs sensor out 1.jpg
    60 KB · Views: 248
This image shows the sensor fully removed.

It is important to note its position when you are lifting the front end to avoid pinching or damaging the wire/sensor.
 

Attachments

  • 16 - abs sensor out 2.jpg
    16 - abs sensor out 2.jpg
    64.6 KB · Views: 248
Please note that the way the PitBull lift supports the bike it impeeds access to the pinch bolt you need to remove.

So prior to lifting the bike I loosened the pinch bolt and loosened the quick release axle and then lifted the bike.

Getting ready to place the bike lift under the fork legs.
 

Attachments

  • 17 -  pitbull prep postion.jpg
    17 - pitbull prep postion.jpg
    99.1 KB · Views: 247
Last edited:
Back
Top